Home › Blogs Article

Wood Subfloor Preparation Before Hardwood Installation: Flatness, Fastening, and Deflection

It can be a real shame if you don’t prepare your subfloor correctly and your beautiful new hardwood flooring doesn’t meet expectations. Whilst a few loose ply boards or inconsistencies may seem insignificant whilst fitting your flooring, you can get frustrated once you have fitted your new flooring.

You may hear noise near the door, or notice movement in specific boards. Sometimes this comes from your hardwood flooring; other times, however, it’s a problem hiding under your flooring.

Wood subfloor preparation for hardwood flooring is an important step. Installers need to know the condition of your current flooring and whether it can support your chosen hardwood.

Areas to focus on include:

Start by Looking at the Existing Subfloor

Every home will be slightly different.

An older property in Denver may have wooden boards for your subfloor, whereas a newer property will likely have some form of plywood or oriented strand board (OSB).

As long as these are in good condition, they can provide a good base for your new hardwood.

First, look for any signs of damage.

Are there any loose areas near your walls? Are any of your panels moving when you walk over them? Has there been any swelling due to dampness?

This will give you an idea of what you may need to address. Whilst it may be quicker to not investigate any issues and fit your new flooring, this can cause a lot of extra work.

How Flat Does a Wood Subfloor Need to Be?

A common misconception is that your flooring needs to be completely level.

However,

This is not the case.

Understanding Flatness and Levelness

If you place a long straight edge down your flooring,

If it is touching the floor, or within the tolerance, then your flooring is relatively even. If there are large gaps under your straight edge, then you may need to fix your subfloor. Your flooring can be slightly sloped but still be even enough for your flooring. However, your flooring may look level but still have a few small dips and raised edges on your panels.

Some flooring manufacturers will allow a tolerance of up to 3/16” over 10ft. Some will have different tolerances. Your correct tolerance will come from your chosen flooring manufacturer’s instructions.

Dealing With High and Low Spots

Raised areas in your ply can be quite common, especially if they have had some moisture-related swelling. If there is a small amount of raised area, an installer can carefully sand down the area to fix. If there is a dip in your flooring, depending on the cause and severity, you may need to replace the damaged panel. Or fix the support underneath. You may need to use a floor patch product that is compatible with your flooring.

Not every leveling product will be suitable for wood flooring. Make sure you use a product suitable for your subfloor and the method you plan to use to fit your hardwood.

Make sure you fix the issue causing the unevenness.

Loose Subfloor Panels Can Become Noisy Floors

You may have been in a home where a specific area makes a noise every time you step on it.

This noise can come from your hardwood, fastening, or subfloor.

If your ply isn’t fixed correctly to your joists, it can cause slight movement. If this happens repeatedly, it can cause materials to rub together.

Finding the Areas That Move

When fitting your hardwood flooring, walk over your exposed subfloor. You may notice some areas flexing, or old nails becoming loose. Some areas may feel solid but make a slight creaking noise. This is important to note as it can be difficult to track down noise once your flooring is fitted.

Choosing the Right Fastening Repair

Sometimes you can add extra screws or fastenings to fix loose panels.

However, if you don’t secure the screw in the right place, it won’t help support your flooring. The screw needs to be fastened properly into your framing. Ensure the length and spacing of your fastenings are compatible with your subfloor.

If the wood around your existing fastener is damaged, or if the panel itself is damaged, you may need to replace the area.

Find out more about other causes of noisy flooring by reading our article on what causes squeaky hardwood floors.

What Subfloor Deflection Means for Hardwood

Some flooring will not make a noise but can feel a bit bouncy. This can be due to deflection.

Deflection is how much a component of your flooring will bend when weight is applied.

Framed flooring will naturally move; however, if it moves too much for your flooring system to reasonably handle, it can cause issues.

Why One Floor May Feel Stiffer Than Another

The framing underneath your subfloor can greatly affect how your flooring feels. The size, spacing, span, and condition of your joists will all play a part in how stiff your flooring feels.

If your flooring feels stiff near an interior support but noticeably bouncy towards the center of the room, this may indicate that you need to check your framing before fitting your hardwood. Whilst this does not necessarily mean your flooring is unsafe, it is something to consider.

When Structural Support Needs Attention

Too much deflection can cause movement in your flooring joints, loose fastenings, and can cause noise. Adding another layer of hardwood will not fix a major framing issue. If you see noticeable sagging, unusual bounce, or damage to your structural components, have a qualified professional inspect your flooring. Depending on the cause, you will need the right solution. Adding extra material to your subfloor can help with movement between your joists but may not fix excessive bending.

Checking Plywood and OSB Before Installation

Not all subfloor damage will be obvious. Your ply may look okay but have weak layers, or your OSB may have swollen edges from long-term moisture exposure. Pay attention to areas near exterior doors, plumbing, and where water may have entered your home. 

Look for any soft areas, separated ply, and damaged corners. Ensure your panel is thick enough for the joist spacing and flooring system above. If your current subfloor doesn’t meet the requirements, you may need to repair it or add extra support. Putting expensive hardwood over weak material will not improve your panel’s condition.

Moisture Testing Is Worth the Extra Attention

Because Colorado has a dry climate, it is easy to forget to consider moisture. However, both your wood flooring and subfloor will be affected by changes in their environment.

During drier periods, your wood can dry out and contract. During higher moisture periods, your wood can absorb moisture and expand. While this is natural, large differences in moisture can cause issues during installation.

Measuring Moisture in the Subfloor

Using an appropriate wood moisture meter, you can check the conditions of your subfloor. This should be done for both your hardwood and wood subfloor. Depending on your flooring product and the manufacturer’s instructions, you will have a required reading and moisture difference.

If your reading is not within the required range,

There may be an unresolved moisture issue, or your materials may need more time in a suitable indoor environment.

Why Moisture Problems Should Be Corrected First

If there is too much moisture in your flooring assembly, your hardwood can swell and cup. Changes in humidity can also cause gaps to appear as your boards dry out. Ensuring your flooring is prepared correctly will not stop all seasonal changes, but it will help you avoid starting your project with the wrong moisture levels.

Does the Installation Method Change Subfloor Requirements?

Yes! Depending on how you are fitting your hardwood flooring, you will need to ensure your subfloor has certain properties. Nailing down requires your subfloor to have reliable fixing points.

Gluing down will require your subfloor to be suitable for the adhesive and flooring product.

Floating engineered hardwood does not require nailing or gluing your planks to your subfloor; however, your flooring will need to meet the manufacturer’s instructions for evenness and stability.

Some systems will require a specific underlay or moisture control product. These products serve specific purposes and will not reliably hide movement or major issues with your flooring.

Learn more about the differences between common installation methods by reading our guide to hardwood installation methods.

What Should Happen Before the First Hardwood Plank Goes Down?

Not all subfloor preparation will be a big repair job. Some homes will only require small fixes to your flooring, cleaning, and ensuring it meets your manufacturer’s requirements. However, some properties will require more work. You may need to fix a raised seam, replace a damaged panel, or check that your flooring is not moving too much.

Your contractor should have a good understanding of your subfloor. Ensure it is even, the panels are fixed, it has the correct support, and the moisture levels are correct.

This is also a good time to clear away any debris and check for any raised fastenings. Taking a little extra time to prepare your flooring will not cause as much disruption as removing your finished flooring to fix an issue.

Hardwood Installation for Denver and Front Range Homes

Flooring can vary from home to home in Colorado. Older properties may have boarded subfloors, previous repairs, or altered framing. Newer properties can also cause issues such as raised seams and moisture exposure during fitting.

With wide-plank flooring and bespoke designs, taking care when preparing your subfloor can make a real difference. The final finish will partly depend on how even your flooring is.

2nd Gen Hardwood offers luxury residential hardwood flooring services to homeowners in Denver and surrounding Front Range communities.

Whether you are updating an older floor or installing new flooring, knowing the condition of your subfloor is an important part of the process.

Final Thoughts

Whilst the work that goes into your flooring will rarely be considered once your room is finished, the quality of your flooring will impact everyday.

Having a stable subfloor will help your hardwood stay well supported. Fixing any loose panels can help reduce unnecessary movement. Knowing your flooring is level and free of structural issues will help avoid tricky repairs.

Taking time to prepare your wood subfloor for hardwood flooring will give your finished flooring a solid base.

If you are looking to install flooring in Denver or a local Front Range community, contact 2nd Gen Hardwood.

Recent Post

Commercial Hardwood Floor Maintenance Plans - A Guide for Facility Managers

Commercial Hardwood Floor Maintenance Plans: A Guide for Facility Managers

Which Direction Should Hardwood Flooring Run - Layout Rules for Open Floor Plans

Which Direction Should Hardwood Flooring Run? Layout Rules for Open Floor Plans

Hardwood Floor Transitions - How to Handle Tile, Carpet, and Uneven Floor Heights

Hardwood Floor Transitions: How to Handle Tile, Carpet, and Uneven Floor Heights

Hardwood Flooring Underlayment - Sound, Moisture, and Subfloor Compatibility

Hardwood Flooring Underlayment: Sound, Moisture, and Subfloor Compatibility